GR PSLR31.13-GTHP-R1R2-1-150-R18 ams OSRAM DURIS® S 5 Red 620 nm Emitter

GR PSLR31.13-GTHP-R1R2-1-150-R18 ams OSRAM DURIS® S 5 Red 620 nm Emitter

- Forward voltage is the field to settle first on this part — six groups spanning 5.60 to 6.80 V at a 150 mA drive, where a 620 nm emitter in a low-voltage 3030 asks for roughly a third of that.
- Two ordering codes are live for the one colour. GTHP covers 24.0 to 30.4 lm and GUHQ 25.9 to 33.0 lm, both drawn from the same four brightness groups.
- The ladder has four rungs, one more than the green and blue members of this platform. GT at 24.0 to 25.9 lm, GU at 25.9 to 28.0, HP at 28.0 to 30.4 and HQ at 30.4 to 33.0.
- 620 nm dominant typical, with colour binned in two CIE quadrilaterals rather than a wavelength ladder. R1 and R2 abut along a single edge; the wavelength tolerance is ±0.5 nm and the coordinate tolerance ±0.005.
- A 12 K/W junction-to-solder rating rests on a 30 % efficiency premise, and the manufacturer's own 278 mW of radiant flux against 937.5 mW of input lands within half a percent of it. Dry-packed to MSL 3, 4500 pieces on a 180 mm reel, a 17.7 mg body with the cathode as the package marking.

Description

Product Introduction

 

 

GR PSLR31.13-GTHP-R1R2-1-150-R18 is a 620 nm red that asks its driver for six volts. Its 150 mA drive point sits at 6.25 V typical, across six groups from 5.60 to 6.80 V - roughly three times what a 620 nm emitter in a low-voltage 3030 asks for.

 

That is the platform's design decision, not a detail. DURIS® S 5 buys its 150 mA test point by running the die at high voltage: 6.25 V at 150 mA is 0.94 W, the same power a low-voltage part reaches at more than double the current. Every other figure here follows from that - the drive window, the thermal load, and the fact that a 3030 pad does not imply a 3030 drive point.

 

Output is binned in four groups, GT through HQ, spanning 24.0 to 33.0 lm, and sold under two live codes: GTHP covers 24.0 to 30.4 lm and GUHQ 25.9 to 33.0 lm, sharing the middle two groups. Colour is binned by coordinate rather than by wavelength band - two CIE quadrilaterals, R1 and R2, abutting along one edge, around a 620 nm dominant typical.

Key Product Features

 

 

1. The Drive Point Comes Before the Colour
Six forward-voltage groups span 5.60 to 6.80 V at 150 mA, so the part draws about 0.94 W at its test point. A 620 nm emitter in a low-voltage 3030 reaches similar power at a far lower voltage and a higher current. A channel sized for one will not serve the other, even though both sit on a 3030 pad.


2. Four Rungs Sold as Two Windows
GT covers 24.0 to 25.9 lm, GU 25.9 to 28.0, HP 28.0 to 30.4 and HQ 30.4 to 33.0. GTHP takes the lower three and GUHQ the upper three, so the two codes share GU and HP. Only GT is exclusive to the first code, only HQ to the second.


3. The Thermal Premise Holds on This Part
The 12 K/W is quoted on a 30 % efficiency assumption, and the manufacturer's own numbers close the loop: 278 mW of radiant flux from 937.5 mW of input is 29.7 %. The published electrical figure therefore needs no correction to speak of - about 17 K/W either way.


4. Colour Binned by Coordinate, Not by Wavelength Band
The colour field on the code is R1R2, two CIE 1931 quadrilaterals sharing the edge between (0.6642, 0.3056) and (0.6591, 0.3176). The 620 nm is a dominant typical; the document allows ±0.5 nm on the measurement itself and sets no upper or lower limit around it, so the coordinate box is what a drawing can hold.


5. One Voltage Ladder Across the Whole Colour Range
The red, the green and the blue members of this platform all print the same six forward-voltage groups, B through G, from 5.60 to 6.80 V. A driver channel designed around one colour member therefore suits the other two - and none of the three suits a low-voltage 3030 channel.

 

Parameter Typical Value
Manufacturer ams OSRAM
Product Series DURIS® S 5
Ordering Code Q65112A1151
Colour of Emission Red; dominant wavelength 620 nm typical, binned by two CIE 1931 quadrilaterals (R1, R2), with no wavelength-group table
Luminous Flux (IF = 150 mA) 24.0 to 30.4 lm under GTHP; the sibling code GUHQ covers 25.9 to 33.0 lm
Forward Voltage (IF = 150 mA) 6.25 V typical across six groups, 5.60 V to 6.80 V
Forward Current 10 to 200 mA continuous, with 300 mA allowed in 10 µs pulses (D = 0.005)
Viewing Angle 120° (Lambertian)
Operating Temperature −40 to 100 °C operating; storage to 125 °C
Thermal Resistance (RthJS) 12 K/W electrical (ηe = 30 %)

Application Fields

 

 

Red sets the warm end of a mixed-white design, and the headings this datasheet files it under run from architecture and garden schemes to mood lighting, medical illumination and photo therapy. Typical specifications include:

 

- Monument and facade wash – a saturated red run along stone or brick, viewed from a distance rather than worked under.
- Bridge and structure accent – long exterior runs where the red has to hold its hue from one end to the other.
- Garden and path marking – exterior features behind a sealed lens, with the red doing the wayfinding.
- Deck and water-feature lighting – a red channel inside a sealed exterior fitting.
- Instrument and examination lamps – built into a luminaire, not offered as a finished product.
- Treatment-panel red bands – a 620 nm band inside a therapy housing, for the maker that carries the registration.
- Mood and accent interiors – a warm red used as a counterpoint in a dim room.
- Window and display work – red picking out a product line against a neutral background.
- Chilled display cabinets – a red channel that makes produce and meat read as fresh under a cool cabinet light.
- Warm-end channels in mixed whites – the red leg of a tunable engine, where its coordinate group decides how the warm point settles.

Why Choose Gainer LED?

 

 

- The voltage question comes first, not last
A buyer who tells us the driver already on the board gets an answer about whether it fits, before a quotation is raised rather than after the first batch is built.


- Since 2012, and only the branded trade
The business has traded branded components from the major manufacturers for fourteen years, with module and fixture builders making up most of the customer list.


- One account covers the whole colour set
A mixed design's colour channels are quoted together, so the buyer settles one set of terms rather than opening an account per part.


- Terms that hold while the build runs
Where a design is locked for a production run, the commercial terms quoted at the first order are the ones held while that build continues.


- A consignment file, not just an invoice
Enquiry, acknowledgement, packing list and dispatch date are kept together, so a traceability request is answered from our own paperwork rather than the carrier's.

FAQ

Q: The page above says 2.11 to 3.36 V. The datasheet says 5.60 to 6.80 V. Which one does the driver get designed to?

A: The datasheet. The range on the listing is a family feature line rather than a figure for this part - its upper end sits below this part's own minimum, so a driver built to it would never reach turn-on. Design to 6.25 V typical and allow the full 5.60 to 6.80 V band. If a supplier quotes the lower range, ask which datasheet paragraph it came from.

Q: We already have a 3030 channel sized for another 3030 red. Can we run this part on it?

A: Not without a change. A 3030 footprint does not fix a drive point: this part wants about 6.25 V at 150 mA, where a low-voltage 3030 red runs near 2 V and is usually driven harder. The current is the smaller problem - a channel that cannot reach 5.6 V will not light the part at all. Check the driver's voltage ceiling before the pad layout.

Q: The applications list on the listing names downlights and chandeliers. Is this part for general lighting?

A: No. Those belong to the white members of the family, and the listing reuses one template across the range. The datasheet puts this emitter under architecture, garden schemes, mood lighting, medical illumination and photo therapy. A 620 nm part is a colour channel - for mixed whites, accents and treatment housings - not a source for room lighting.

Q: The thermal figure is quoted on a 30 % efficiency assumption. Does that assumption hold here?

A: Yes, and unusually well. The manufacturer publishes 278 mW of radiant flux against roughly 937.5 mW of input at its 150 mA drive, which works out at 29.7 %. So the 12 K/W can be used as printed for junction arithmetic; corrected for that premise it lands near 17 K/W, a difference of well under a percent.

Q: The listing says "RoHS Complaint" and the datasheet never mentions RoHS. What do we file?

A: Take the compliance statement from the manufacturer's declaration, not from a listing. The datasheet's notes cover eye safety, moisture level and the medical exclusion, and it makes no RoHS claim at all; the listing's line is a family blurb with a typo in it. For a compliance file, request the current declaration alongside the datasheet revision.

 

Hot Tags: GR PSLR31.13-GTHP-R1R2-1-150-R18 ams OSRAM DURIS® S 5 Red 620 nm Emitter, China GR PSLR31.13-GTHP-R1R2-1-150-R18 ams OSRAM DURIS® S 5 Red 620 nm Emitter manufacturers, suppliers, factory, PLT5 520DB P, SFH 203, LR E67F ABCB 46 G3R3 50 R18 Z, GW JTLMS1 CM G7H2 XX57 1 60 R33, LZ7-04M2PD-0000, SFH 4728AS A01

You Might Also Like

Shopping Bags