
OSRAM DURIS® S 5 GW PSLT33.EM-LWL1-XX55-1-150-G3-R18 4000K CRI 80 135–160lm 6.13V-Class 3030
Package & Size: 3.00 mm × 3.00 mm × 0.65 mm SMD, 1212 (3030 metric), 120° Lambertian, colored diffused silicone resin;
CCT & CRI: 4000 K neutral white, CRI min. 80 (typ. 82), R9 min. 0, chromaticity centre 0.3818 / 0.3796;
Test Condition: 150 mA / 6.13 V (typ.), flux 135–160 lm at 25°C (148 lm typical), efficacy approx. 161 lm/W;
Drive & Thermal: 200 mA max continuous current; package thermal resistance 7.7°C/W; −40°C to +100°C operating range; MSL 3.
Description
Product Introduction
The GW PSLT33.EM-LWL1-XX55-1 belongs to ams OSRAM's DURIS® S 5 platform-a 4000 K neutral white, CRI 80 LED in a 3030 package, mid-power class. DURIS S 5's positioning within ams OSRAM's portfolio is clear: a standard 3030 footprint and 6V-class forward voltage covering panel lights, linear luminaires, downlights, and retrofits in indoor general lighting. 4000 K is one of the most "scene-agnostic" CCTs in indoor lighting-crisper than 3000 K, softer than 5000 K-finding a place in offices, retail, hospitality back-of-house, and industrial environments; CRI 80 meets routine commercial rendering requirements, keeping "colors from drifting too far."
The electrical profile is the core interface in real designs: at the 150 mA test point, a 6.13 V typical forward voltage corresponds to roughly 0.92 W electrical power; flux lands in the 135–160 lm window, 148 lm typical, with efficacy around 161 lm/W. The 200 mA maximum continuous current leaves about 1.3 times the headroom for designs needing slightly higher brightness; the 7.7°C/W package thermal resistance is routine for a 1 W-class 3030, and a standard FR-4 board is typically sufficient near 150 mA. The 120° Lambertian output with 0.65 mm low height and diffused silicone resin forms an even neutral-white surface behind a diffuser.
Key Product Features
- 4000 K + CRI 80 as a "neutral-white baseline": 4000 K avoids the yellow lean of 3000 K and the cool lean of 5000 K, easily achieving "neither warm nor cold, clean and neutral" in office, retail, and hospitality back-of-house spaces. CRI 80 (typ. 82) meets routine commercial rendering requirements, and R9 minimum of 0 means deep-red rendering is not its strength-if the project involves apparel fabrics or food display where "color judgment" matters, CRI 90+ options are more appropriate. This device's value lies in "general-purpose," not "extreme color rendering."
- 135–160 lm brightness window with 161 lm/W efficacy: 148 lm typical at 150 mA is a balanced level in a 1 W-class 3030. For panel and linear lights that use multi-emitter arrays to reach target illuminance, this window keeps emitter density within a reasonable range rather than resorting to dense packing. 161 lm/W is a usable efficacy level within CRI 80 neutral white.
- 6.13 V-class forward voltage with 200 mA maximum continuous current: A 6V-class device requires lower drive current at the same power, placing comparatively gentler stress on constant-current drivers and less loss on long-strip harnesses. The 200 mA maximum continuous current leaves about 1.3 times the headroom for designs needing slightly higher brightness, though raising current increases thermal load-confirm board heat spreading and driver capability before using the headroom. The device also tolerates 400 mA short-pulse surge (≤10 μs), leaving some operating room in PWM dimming scenarios.
- 7.7°C/W package thermal resistance with 0.65 mm low height: At the 0.92 W power class, 7.7°C/W allows FR-4 boards to meet thermal needs near 150 mA without a metal-core PCB for this device alone. The 0.65 mm height suits slim panel and linear fixtures, and the 120° output forms an even surface behind a diffuser.
| Item | Value |
| Manufacturer | ams OSRAM |
| Series | DURIS® S 5 |
| Package | 3030,3.00 × 3.00 × 0.65 mm,SMD |
| CCT | 4000 K |
| CRI | 80 |
| Flux @ 150 mA, 25°C | 135 – 160 lm |
| Vf (Typ.) | 6.13 V |
| Max Continuous Current | 200 mA |
| Viewing Angle | 120° |
| Thermal & Top | 7.7°C/W;−40°C - +100°C |
Application Scenarios
DURIS S 5's official positioning covers indoor general lighting, linear lights, downlights, and retrofits. Combined with 4000 K CRI 80, the 135–160 lm brightness window, and 6.13 V-class drive, the practical landing spots for this device in legacy projects are indoor scenarios that need "a neutral-white baseline, even illumination, and mid-range brightness":
- Office and commercial base lighting modules: 4000 K provides a neutral-white base in office spaces that is crisper than 3000 K and softer than 5000 K, and CRI 80 renders material colors sufficiently for routine office environments. The 150 mA drive and 7.7°C/W thermal resistance allow FR-4 boards to handle heat spreading, so the fixture structure needs no extra thermal design. For linear or panel lights already built around the XX55 bin, the replacement GW QSLPS1.EM-LYL1 moves the flux lower bound from 135 lm up to 145 lm-landing requires confirming in the original diffuser whether the brightness shift alters target-surface illuminance or glare balance.
- Downlights and directional luminaires: The 135–160 lm flux makes brightness configuration manageable in small-to-mid aperture downlights, and the 120° output diffuses into a soft downward distribution. 4000 K neutral white suits base lighting in retail, hospitality back-of-house, and commercial spaces. The replacement continues the package and 120° output, concentrating landing engineering on brightness validation and 6.19 V Vf drive confirmation.
- Linear lights and strip modules: The 6V-class drive is comparatively less sensitive to harness voltage drop on long strips, and 135–160 lm per emitter lets a strip reach target illuminance at reasonable density. The 0.65 mm height suits slim linear fixtures, and the 120° diffused output forms an even surface behind a diffuser.
Why Choose Gainer LED?
- 14 years in distribution with practical judgment on the rhythm of "PDN-designated replacement" landings: OS-PDN-2025-053 designates GW QSLPS1.EM-LYL1-XX55-1 for the XX55 bin-this is not an open-ended substitute search but a generational transition with a defined target part number. Gainer's long-term tracking of OSRAM discontinuation notices and replacement paths helps customers break "LWL1 is discontinued, can GW QSLPS1.EM-LYL1 work" into executable steps: verify the flux window and Vf delta first, then validate physically in the original fixture-rather than re-running a full selection cycle in front of a "discontinued" label.
- Hands-on understanding of subtle drive differences across 6V-class 3030 platforms: The Vf shift from 6.13 V to 6.19 V is only 60 mV, but in a constant-current driver it can affect output voltage headroom and efficiency. Gainer regularly handles landing questions between 6V-class platforms and can help customers judge whether the existing driver can be used as-is or needs its constant-current setting adjusted during the transition-rather than comparing Vf numbers alone.
- Small-batch sample support for a "validate flux lower-bound shift and Vf delta before committing to volume" landing rhythm: Moving from 135–160 lm to 145–160 lm shifts the flux lower bound up by roughly 10 lm, which may show up as higher target-surface illuminance or changed glare in the original fixture. Gainer supports small-batch R&D sample purchases, letting customers compare a few dozen replacement samples under real optical and drive conditions-without committing to the 4,500 pcs minimum order quantity just to validate.
- One-stop LED, driver, and optics kit to reduce cross-supplier confirmation during landing: When switching from DURIS S 5 to OSCONIQ E 3030, the package size and 120° output are consistent, but the Vf delta and upward brightness shift may require re-confirming drive current settings and diffuser matching. Gainer covers LEDs, constant-current driver ICs, and optical accessories, letting customers verify emitter, driver, and optics matching through one channel rather than relaying parameters among three separate suppliers.
- Factory packaging with lot labels intact for traceability during the parallel phase of residual replenishment and landing validation: While LWL1 residual is being consumed and replacement landing samples are being validated, two series may coexist on the production line. Gainer ships in original reels or cut tape with lot and bin labels preserved, supporting series- and bin-isolated feeding-reducing brightness or CCT deviation from mixed materials during the parallel phase.
FAQ
Q: The PDN-designated replacement GW QSLPS1.EM-LYL1-XX55-1 has a different flux window-can I use it directly?
A: The package (3030), CCT (4000 K), CRI (80), viewing angle (120°), and drive interface (150 mA / 6V-class) are all consistent, so drive-level continuity is solid-but the flux window moves from 135–160 lm to 145–160 lm, with the lower bound up by roughly 10 lm; Vf shifts slightly from 6.13 V to 6.19 V. This means the dimmest bin's actual brightness at the same drive current will increase somewhat. If your fixture thermal design was built around the original 135 lm lower bound, re-confirm junction temperature and target-surface illuminance are still within tolerance; if the original design felt brightness-limited, the replacement's upward lower bound may actually be an improvement. Landing validation should use a small set of replacement samples in the original fixture for brightness and thermal comparison-rather than skipping physical confirmation just because "the PDN says so."
Q: Does the 6.13V to 6.19V Vf difference require adjustment in my constant-current driver?
A: The difference is only 60 mV, and for most constant-current drivers this falls within output voltage headroom-no driver topology redesign is needed. But two things should be confirmed: first, whether the driver's maximum output voltage at the target current still covers 6.19 V plus harness and connector drops; second, if the driver operates near its voltage ceiling, a 60 mV shift could affect efficiency or protection margin. Before substituting, measure the actual operating point of the existing circuit on a replacement sample rather than comparing datasheet Vf numbers alone. If the driver has ample headroom, direct use is usually fine; if it was already near the limit, evaluate whether to adjust the constant-current setting or change the driver.
Q: How does 4000K CRI 80 compare with the 3500K or 5000K I currently use for office and commercial spaces?
A: 4000 K sits between 3500 K's "warm neutral" and 5000 K's "crisp cool white"-visually cleaner and sharper than 3500 K, with less cool cast than 5000 K. Office and commercial base lighting often favors the 4000 K range for clarity; if a more relaxed, warmer atmosphere is needed (hotel guest rooms, residential living spaces), 3500 K or 3000 K fits better; extremely cool white at high illuminance (industrial high-bay, tunnels) would bring 5000 K or 5700 K into consideration. CRI 80 is a reasonable trade-off in general lighting where "seeing clearly without color shift" is the primary task, but if color judgment is involved (apparel fabrics, food display), CRI 90 options should be considered. Compare physical samples at the target illuminance.
Q: What are the standard pack and MOQ? Can I get a small set of replacement samples for landing comparison?
A: The Rutronik page lists a 4,500 pcs reel packaging unit and a 4,500 pcs minimum order quantity for this family, with a factory lead time of roughly 14 weeks. This is a high threshold for landing validation. Landing comparison typically needs only a few dozen replacement samples-confirm directly with your supplier whether Cut Tape or break quantities are available, along with minimums and lead time. If break quantities are not feasible, evaluate whether channel can cover validation, rather than placing a 4,500 pcs order for a few dozen samples. The focus is confirming the 145–160 lm window's brightness behavior and 6.19 V drive compatibility in the original fixture; sample quantities only need to cover the main test scenarios.
Hot Tags: OSRAM DURIS® S 5 GW PSLT33.EM-LWL1-XX55-1-150-G3-R18 4000K CRI 80 135–160lm 6.13V-Class 3030, China OSRAM DURIS® S 5 GW PSLT33.EM-LWL1-XX55-1-150-G3-R18 4000K CRI 80 135–160lm 6.13V-Class 3030 manufacturers, suppliers, factory, PLT5 520B, SFH 7015, GR CS8PM1 23 KPKR 1, GW JTLPS1 CM JNKN XX55 1, led smd white, GW QSLMS1 KM H7H9 XX32 1
Send Inquiry
You Might Also Like
-

OSRAM OSCONIQ® P 3030 GT QSSPA1.13-LSLU-26-1-350-R18...
-

OSRAM DURIS® S 5 GY PSLM31.13-HQHS-5F5G-L2M2-100-R18...
-

OSRAM OSLON® Square GW CSSRM2.PM-N4N6-XX53-1-700-R18...
-

ams OSRAM DURIS® E 2835 GW JTLRS1.EM-K5L4-XX57-1-100...
-

LSG T676-P7R-1-0+N7P9-24-0-20-R18-ZB ams OSRAM Multi...
-

ams OSRAM LR T64F-CBDB-1-1-20-R33-Z High-Contrast 62...

