
GW PUSRA1.PM-N5P2-XX55-1-700-R33 ams OSRAM's OSCONIQ® P 3737 4000K
- Group 35 is the chromaticity group this code belongs to, and the figure on page 7 is where the number is printed — its eight ellipses run 31 to 38 from the cool end, and the ordering field XX55 carries the same two digits.
- A 320 to 390 lm output window at the 700 mA drive point, measured at an 85 °C junction. The N5P2 pair brackets seven of the family's eight brightness groups, so one code spans the whole window.
- 2.84 V typical, with production spread across 2.70 to 3.20 V, five bands of 0.10 V from K2 to M2.
- Cx 0.3818 and Cy 0.3796 place the neutral point — one window of 0.0094 × 0.0041 at three steps, a second of 0.0157 × 0.0068 at five, the pair tilted 53.4°.
- CRI 70 at the floor, 72 typical, R9 no lower than −50, the rendering figures scoped to 3000–6500 K. The 2.1 K/W junction-to-solder figure is an electrical one, drawn on a 50 % conversion premise.
Description
Product Introduction
The figure and the ordering table each list eight colour points, and they are not the same eight. The figure runs 2700 K to 6500 K; the table runs 3000 K to 8000 K. Seven of the points carry a published colour box, and this is one of them.
The code this range sells at 4000 K is GW PUSRA1.PM-N5P2-XX55-1, recorded as Q65113A3977. Its output band is 320 to 390 lm at 700 mA, on a 2.84 V typical and a 120° Lambertian beam, in a 3.7 × 3.7 mm epoxy body.
The colour field repays a second look. The figure numbers its ellipses 31 through 38 from the cool end, and the field's last two digits reproduce them exactly: XX51 at 6500 K, XX55 here, XX57 at 3000 K. The document never states the mapping; it is read off the drawing.
The orderable figures: 320 to 390 lm across seven brightness groups, five voltage bands spanning 2.70 to 3.20 V, CRI 70 at the floor with R9 no lower than −50, and a centre at Cx 0.3818 / Cy 0.3796.
Key Product Features
1. The Colour Field Is a Chromaticity Group Number
The figure on page 7 numbers its eight ellipses 31 to 38, running from the cool end of the range to the warm end. The ordering table's colour field runs XX51 to XX57 across the same points, and all seven agree: the field's last two digits are the group number. The document never says as much. Nothing in the ordering information calls those digits a group number; that reading comes from the drawing, and from the reel label.
2. The Code With No Colour Group Is Also the Code With a Different Field
Seven codes write their colour field as XX5n. The eighth writes 80PC, and it is the 8000 K entry. That is the only structural break in the ordering table, and it lands on the one colour point the figure does not draw.
3. Seven Sold Points Have Published Geometry; the Eighth Has None
The chromaticity table carries seven rows, 3000 K through 6500 K, and the two corner tables that follow cover the same seven. The 8000 K code appears in the ordering table and in no colour table at all - no centre, no three-step or five-step ellipse, no sub-group corners. An 8000 K order has a flux band and a voltage ladder and nothing else to put on a drawing.
4. The Rendering Figures Stop Short of the Advertised Range
The characteristics table attaches a range to its colour rendering rows: CRI 70 minimum and 72 typical for 3000 K to 6500 K. The feature list on the opening page advertises the family across 3000 K to 8000 K. The 8000 K code therefore sits inside the advertised span and outside the measured one, and the R9 row carries a floor of −50 with no typical beside it at all.
5. The 4000 K Point, Published to Its Sub-Groups
Cx 0.3818 and Cy 0.3796 locate the neutral point. Two windows are drawn around it - 0.0094 × 0.0041 at three steps and 0.0157 × 0.0068 at five - with the ellipse set at 53.4°. The point is then divided into eight sub-groups, A through H, whose corner coordinates are printed in full, so a receiving bench can draw its own acceptance box instead of borrowing one.
| Parameter | Specification |
| Ordering code | Q65113A3977 (GW PUSRA1.PM-N5P2-XX55-1) |
| Colour temperature | 4000 K, chromaticity group 35; centre Cx 0.3818 / Cy 0.3796 |
| Luminous flux | 320 to 390 lm at 700 mA, 85 °C junction (groups N5 to P2) |
| Forward voltage | 2.84 V typical; 2.70 to 3.20 V across five bands, K2 to M2 |
| Forward current | 100 to 1500 mA; 2000 mA permitted in 10 µs pulses at a 0.005 duty cycle |
| Colour rendering | CRI 70 minimum / 72 typical (3000–6500 K); R9 minimum −50 |
| Viewing angle | 120° at the half-intensity points, Lambertian emission |
| Thermal resistance | 2.1 K/W junction-to-solder, electrical basis at a 50 % conversion premise |
| Operating temperature | −40 to 125 °C; junction maximum 135 °C; storage −40 to 125 °C |
| Package and packing | 3.7 × 3.7 mm epoxy body with silicone lens; 43.0 mg; reel of 330 mm carrying 3000 pieces; MSL 2 |
Application Fields
- Sports halls and gymnasium courts – the indoor heading, over a playing surface where a neutral cast is written into the lighting standard.
- Touring and festival wash lighting – the entertainment heading, in fixtures rigged and struck on a nightly cycle.
- Theme-park and attraction wash – exterior effects work where the fitting has to survive weather and repetition.
- Loading-dock and canopy lighting – the outdoor heading, aimed at vehicles rather than at people.
- Container-yard and port floodlighting – long-throw fittings mounted high on cranes and masts.
- Railway platform and marshalling-yard lighting – open sites where a fitting is serviced from a tower.
- Quarry and aggregate-site area lighting – dust, vibration and a maintenance visit measured in years.
- Cold-store and refrigerated-aisle lighting – interior work where the board runs cold and the flux reference does not.
- Aircraft hangar and apron lighting – very high mounting heights where the 390 lm ceiling sets the array size.
- Foundry and heavy-fabrication task lighting – interiors where the luminaire is part of the process equipment.
Why Choose Gainer LED?
Stock, documents and dates are the three things a buyer cannot repair once the goods have left. All three are handled here:
- Fourteen years on the same component categories - the desk has traded branded optoelectronics since 2012 without drifting into other product lines.
- A parts list from several makers on one quotation - emitters, optics and drivers priced, acknowledged and shipped together rather than split across separate suppliers.
- Cross-references answered from stock rather than from a catalogue - where a drawing names something we do not hold, the nearest equivalent we do hold is offered with its differences spelled out.
- Stock and lead time given for the exact code, with a date attached - not for the series, and not as a range that shifts when the order is placed.
- Export documents prepared to the destination before dispatch - invoice, packing list, declaration of origin and reel labels checked against what the receiving country asks for.
FAQ
Q: How do we read the colour field in this part number?
A: The field's last two digits are the chromaticity group. The diagram on page 7 numbers its eight ellipses 31 to 38 from the cool end, and the ordering table's XX51 through XX57 reproduce those numbers exactly - XX55 is group 35, the 4000 K point. The datasheet never states the mapping, so confirm it against the figure rather than assuming it, and quote the group on the order line.
Q: We need 8000 K from this range. What colour data comes with it?
A: The code exists - N5P2-80PC-1, filed as Q65113A3980 - and its row reads 320 to 390 lm. It is alone in the table in having no colour box published. There is no centre, no three-step or five-step ellipse and no sub-group corners for it, and the rendering rows are scoped to 3000 K to 6500 K. An 8000 K drawing cannot be given a chromaticity tolerance from this document.
Q: Does the CRI 70 figure apply to every colour point in the family?
A: No. The characteristics table attaches a range to its rendering rows - 3000 K to 6500 K - while the feature list advertises the family from 3000 K to 8000 K. The 8000 K code falls inside the advertised span and outside the measured one. Write the colour point into any CRI clause, and note that R9 is given as a floor of −50 with no typical beside it.
Q: What drive window and thermal figure should the board be designed to?
A: Current runs from 100 mA to 1500 mA, with a 2000 mA allowance in 10 µs pulses at a 0.005 duty cycle, and everything is specified at a 700 mA drive, on an 85 °C junction. The published thermal figure is 2.1 K/W stated on an electrical basis at a 50 % conversion premise, so a heatsink calculation should start from roughly double it.
Q: What arrives on the reel, and how is it protected?
A: 3000 pieces on a 330 mm reel, in a moisture-barrier bag at MSL 2 with a floor time of one year once opened, and a corrosion test to class 3B. The emitter is 43.0 mg and carries its cathode marking on the package. Check the group number on the reel label against the order line before the reel reaches the machine.
Hot Tags: GW PUSRA1.PM-N5P2-XX55-1-700-R33 ams OSRAM's OSCONIQ® P 3737 4000K, China GW PUSRA1.PM-N5P2-XX55-1-700-R33 ams OSRAM's OSCONIQ® P 3737 4000K manufacturers, suppliers, factory, SFH 4717AS A01, GR CS8PM1 23 KPKR 1, SFH 4640, LY R976 PS 36 0 20 R18, SFH 7015, SPL PL90 3
Send Inquiry
You Might Also Like
-

GW PSLR31.EM-LQLR-XX58-1-150-R18 2700K ams OSRAM DUR...
-

GW CSSRM3.PM-N6N8-XX52-1-700-R18 5700K Cool White OS...
-

ams OSRAM GW JTLPS1.EM-KKLN-XX51-1-150-C High-Perfor...
-

ams OSRAM SFH 4059SR MIDLED® 850nm High-Power Sidelo...
-

ams OSRAM LR T64F-CBDB-1-1-20-R33-Z High-Contrast 62...
-

ams OSRAM GW JTLPS1.EM-JMLM-XX58-1 High-Efficacy 270...

